Honeywell ScanPal EDA52 Mobile Computer
Honeywell ScanPal EDA52 Handheld Computer
Honeywell ScanPal™ EDA52 is an enterprise-class mobile computer that provides reliable and secure connectivity between frontline workers and backend systems. It’s designed for retail use, logistics, manufacture, healthcare and public service.
ScanPalEDA52 is Honeywell’s next generation ScanPal series mobile computer equipped with the latest Qualcomm Snapdragon octa-core 2.0GHz processor and robust wireless connectivity through NFC, Wi-Fi5, Bluetooth5.1 and 4GLTE communication.
Honeywell ScanPal EDA52 Specifications
FEATURES
- Camera
- Yes
- Housing Grade
- Standard
- Healthcare
- Features
- Rugged
DIMENSIONS
- Overall Dimensions
- 159mm x 75 mm x 14.4 mm (6.26 in x 2.95 in x 0.57 in)
SCANNING SPECIFICATIONS
- Decode Capability
- Honeywell S0703 Slim Imager (1D/2D barcode symbologies)
NETWORK
- Bluetooth Specifications
- Bluetooth Class 5.1
- GPS Specifications
- GPS (WWAN only) Supported Protocols: Simultaneous receiver support for GPS, GLONASS, and BeiDou
- WWAN Specifications
- WWAN Radio:
- GSM/EDGE: Bands 2, 3, 5, 8
- WCDMA: Bands 1, 2, 4, 5, 6,8, 9, 19
- FDD-LTE: Bands 1, 2, 3, 4, 5, 7, 8, 9, 12,13,17,19,20,25,26,28,30,66
- TDD-LTE: Bands 38, 39, 40, 41
- WLAN Specifications
- WLAN (Wi-Fi Alliance certified) :
- IEEE 802.11 a/b/g/n/ac
- Additional WLAN Features:
- 802.11 d/e/h/i/k/ r/u/w
- WLAN Security: OPEN, WEP, WPA/WPA (Personal and Enterprise WPA2), WPA3 (OWE, SAE,Enterprise)
- WLAN Supported EAP:TLS, PEAP, TTLS, PWD, LEAP
SOFTWARE & FIRMWARE
- Operating System
- Android 11, and upgradeable to Android 13
- ** Android 13 is pending for the confirmation from Qualcomm & Google
MEMORY & DATA
- Memory
- 3 GB RAM/32 GB Flash; 4 GB RAM/64 GB Flash; 6 GB RAM/128 GB Flash，
- Storage Expansion: MicroSD (up to 128 GB)
HARDWARE
- Processor
- Qualcomm Snapdragon SM6115, Quad high-performance Kryo cores 2.0 GHz +Quad low-power Kryo cores 1.8 GHz
- Display Resolution
- 1440 x 720 High Definition
- Display Size
- Gorilla Glass 5, 5.5-inch
- Scan Engine Range
- Standard
- Scan Engine Model
- Honeywell S0703 Slim Imager (1D/2D barcode symbologies)
ELECTRICAL
- Battery Capacity
- 3.8 V, 4,500mAh, removable
- Battery Type
- Li-Ion
ENVIRONMENTAL
- Operating Temperature
- -20°C to +50°C (-4°F to +122°F)
- Storage Temperature Range
- – 4 – 158 °F
- – 20 – 70 °C
- Operating Humidity
- 5 – 90 % (non-condensing)
STANDARDS & APPROVALS
- Drop Specifications
- Multiple 1.3m (4.3ft) per MIL-STD 810G drops to concrete at room temperature
- Multiple 1.5m (5ft) per MIL-STD 810G drops with rubber boot concrete at room temperature
- Tumble Specifications
- Tumble: 550 times at 0.5 m (1.64 ft)
- Durability
- Environmental Sealing: IP67. Electrostatic Discharge (ESD): ±8 kV direct; ±15 kV air
OTHERS
- Camera Position
- Rear Camera: 13-megapixel color camera; Front Camera: 5-megapixel color camera
- Keyboard
- Yes
SERVICE TERMS
- Warranty Duration
- One-year factory warranty
Industry Use
Field Mobility
Healthcare
Light Warehouse
Transportation
Retail
Manufacturing
Request a Repair
If you have a problem with your Honeywell ScanPal EDA52 then pleaase use the link below to get an online RMA
Request a Quote
Do you need a number of terminals. Let us know the hardware configuration and we’ll get back to as soon as possible.
Request Help
If you need any technical assistance regarding your terminals then please dont hesitate to contact us.
Knowledge Base – Honeywell ScanPal EDA52
Soft Reset - Warm Boot
Honeywell ScanPal EDA52 Soft Reset – Warm Boot
Perform a soft reset if applications stop working.
1. Press and hold the Power Button until the options menu appears.
2. Select Restart or Power > Restart depending on your computer model.
The device reboots.
Hard Reset - Cold Boot
Honeywell ScanPal EDA52 Hard Reset – Cold Boot
CAUTION: Performing a hard reset with a microSD card installed in the device may cause damage or data corruption to the microSD card. All un-saved data is lost after performing a hard reset.
To restart the computer if the touch panel display is unresponsive:
• Press and hold the Power Button for approximately 8 seconds until the computer restarts.
Enterprise Reset
Honeywell ScanPal EDA52 Enterprise Reset
You can perform an Enterprise data reset if a reboot did not improve the condition and all other troubleshooting methods have not been resolved the issue. This method provides a clean configuration for troubleshooting by erasing all the data from the internal shared storage location on the mobile computer. Data is not erased from the IPSM card location.
Caution: An Enterprise data reset results in data loss, only perform this procedure if all other recovery methods have failed. All personal content is erased including, but not limited to emails, pictures, contacts, Google account information, system settings, and application settings.
Note: This method of recovery may not be available if your system administrator has set policies to prevent the reset use.
Before you begin
- If you recently reset your Google Account password, wait 24 hours before performing an Enterprise data reset.
- Make sure you have your screen lock password, PIN, or pattern if you activated one. You will need this to reset the mobile computer.
- If you have a Google Account, backup your data and settings to your Google Account so you can restore them if required.
- Connect the computer to an external power source or make sure you have a full battery charge.
- Make sure you have an Internet connection.
Enterprise Data Reset the Mobile Computer
- Swipe up from the bottom of the home screen to access all applications.
- Select Settings > System > Reset Options.
- Tap Enterprise Data Reset.
- Tap Erase All Data.
- If prompted, type your screen lock security patter, PIN, or password, and tap Next.
- Tap Erase Everything. A message appears informing you an Enterprise Data Reset is being performed.
Terminal will reboot.
Factory Reset
Honeywell ScanPal EDA52 Factory Reset
A full factory reset should only be performed if you have exhausted all other troubleshooting options. This method reverts the mobile computer back to the factory state by erasing all data in Internal shared storage and the IPSM Card storage locations on the mobile computer.
Caution: A full factory reset results in data loss, only perform this procedure if all other recovery methods have failed and have no other option. All personal content is erased including, but not limited to emails, pictures, contacts, Google account information, system settings, and application settings.
Note: This method of recovery may not be available if your system administrator has set policies to prevent the reset use.
Before you begin
- If you added a Google Account to the mobile computer, make sure you have your Google username and password associated with the computer. If you do not have the username and password, you will not be able to use the mobile computer after the reset. This is a security measure that prevents unauthorized users from using the device if they try a Full factory reset.
- If you did not add a Google Account to the mobile computer, the extra security level is not enabled, and you will not need a Google username and password.
- If you recently reset your Google Account password, wait 24 hours before performing an Enterprise data reset.
- Connect the computer to an external power source or make sure you have a full battery charge.
- Make sure you have an Internet connection.
Factory Reset the Mobile Computer – From the Operating System
- Swipe up from the bottom of the home screen to access all applications.
- Select Settings > System > Reset Options.
- Tap Erase All Data (Factory Reset)
- Tap Reset Phone.
- If prompted, type your screen lock security patter, PIN, or password, and tap Next.
- Tap Erase Everything. A message appears informing you an Enterprise Data Reset is being performed.
Terminal will reboot.
Factory Reset the Mobile Computer – From the Bootloader/Recovery Mode
- Press and hold the Power Button.
- From the menu that will appear on the screen select to Power Off.
- With the device off press and hold the Volume Down Button, while doing so press the Power Button.
- In the bootloader, select “Recovery”.
- While in recovery mode, press the Volume Down Button for 10 seconds to see all options.
- Select “Wipe data/factory reset” and press the Power Button.
- Select “Reboot System now” and press the Power Button.
Terminal will reboot.
Honeywell ScanPal EDA52 SKU’s
- EDA52-11AE34N21RK EDA52, 2-pin interface port, Android 11 with GMS, WWAN & LAN, S0703 Imager, 2.0GHz Octa-ore, 3GB/32GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB type C
- EDA52-00AE31N21RK EDA52, 2-pin interface port, Android 11 with GMS, WLAN, S0703 Imager, 2.0GHz Octa-core, 3GB/32GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB type C
- EDA52-11AE6AN21RK EDA52, 6-pin interface port, Android 11 with GMS, WWAN & WLAN, S0703 Imager, 2.0GHz Octa-core, 4GB/64GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh
- EDA52-11AE64N21RK EDA52, 2-pin interface port, Android 11 with GMS, WWAN & WLAN, S0703 Imager, 2.0GHz Octa-core, 4GB/64GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB type C
- EDA52-00AE61N21RK EDA52, 2-pin interface port, Android 11 with GMS, WLAN, S0703 Imager, 2.0GHz Octa-core, 4GB/64GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB type C
- EDA52-11A034N21RK EDA52, 2-pin interface port, Android 11 with GMS, WWAN, S0703 Imager, 2.0 GHz Octa-core, 3GB/32GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB type C
- EDA52-00AE6BN21RK EDA52, 6-pin interface port, Android 11 with GMS, WLAN, S0703 Imager, 2.0GHz Octa-core, 4GB/64GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh
- EDA52-00AE81N21RK EDA52, 2-pin interface port, Android 11 with GMS, WLAN, S0703 Imager, 2.0GHz Octa-core, 6GB/128GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB type C
- EDA52-11AE84N21RK EDA52, 2-pin interface port, Android 11 with GMS, WWAN & WLAN, S0703 Imager, 2.0GHz Octa-core, 6GB/128GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB type C
Healthcare
- EDA52-0HA761N21RK EDA52 Healthcare, 2-pin, Android 11 with GMS, WLAN, N3601 Imager, 2.0GHz 8 core, 4GB/64GB Memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, Battery 4500 mAh, USB Type C, disinfectant-ready housing.
- EDA52-0HAE61N21RK EDA52 Healthcare, 2-pin interface port, Android 11, LAN, S0703 Imager, 2.0GHz Octa-ore, 4GB/64GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB type C, disinfectant-ready housing.
- EDA52-1HAE34N21RK EDA52 Healthcare, 2-pin interface port, Android 11, WAN, S0703 Imager, 2.0GHz Octa-ore, 3GB/32GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB type C, disinfectant-ready housing.
- EDA52-1HAE64N21RK EDA52 Healthcare, 2-pin interface port, Android 11, WAN, S0703 Imager, 2.0GHz Octa-ore, 4GB/64GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB type C, disinfectant-ready housing.
- EDA52-1HA764N21RK EDA52 Healthcare, 2 pin, Android 11 with GMS, WWAN & WLAN, N3601 Imager, 2.0GHz 8 core, 4GB/64GB Memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB Type C, disinfectant-ready housing.
- EDA52-0HA731N21RK EDA52 Healthcare, 2-pin interface port, Android 11 with GMS, WLAN, N3601 Imager, 2.0GHz 8 core, 3GB/32GB Memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, Battery 4500 mAh, USB type C, disinfectant-ready housing
- EDA52-0HAE31N21RK EDA52 Healthcare, 2-pin interface port, Android 11, LAN, S0703 Imager, 2.0GHz Octa-ore, 3GB/32GB memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB type C, disinfectant-ready housing.
- EDA52-1HA734N21RK EDA52 Healthcare, 2-pin, Android 11 with GMS,WWAN & LAN, N3601 Imager, 2.0GHz 8 core, 3GB/32GB Memory, 13MP+5MP cameras, Bluetooth 5.0, NFC, battery 4500 mAh, USB Type C, disinfectant-ready housing.